Aluminum Expanded Mesh offcuts 126 cm x 31 random, fine expanded mesh, useful for Filtering air-water-fuel,
This is for an extension cable for DC/AC Low Voltage 18V 12V 9V or less. The plug is 5.5mm Barrel Style, Extension Power Cable 10ft Long for DC/AC powered devices that use a 5.5mm x 2.1mm inner. This will help you make your AC or DC Adapter reach further. A very handy adapter cable around the home or office. DC/AC power female to male extension cable Specification: 2.1 mm center pin 10 feet of cable DC/AC plug diameter: 5.5mm outer / 2.1mm inner 18 Sold 51 in Stock
This is a well equipped Pump (hoses fitting Etc) needs a bit of woodwork on two locker doors hinge and the back of the crew cabin,I think it is in very good condition for its age and runs well, with its V8 diesel. It has all the standard equipment. It spent all its working life at a training centre and still carries the badge on the door so it is very low mileage, the ladder was changed by the training centre and it was fitted with a foam tank,but it needs replacing, they also fitted disc brakes to it and more or less it is ready to go, tax and MOT exempt,it has BA's helmets and a fireman's dress uniform,
Great for a Live-in van or a Trailer for a steam engine. You are buying a set of 4 solid steel wheels with bonded tyres about 32” in diameter and 6” wide, with a steel axle 59” between the inside of the wheels 2 5/8” square solid steel covered with wood, the wood is 12” x 6”, held on with bolts and cross plates. The width is 80” outside the hubs with the springs and hangers on, but need rebuilding, the wooden and steel turntable is there, but, only as a Patterns. The wheels and axles formed part of a Trailer that was used to remove steel & scrap for the late Marconi factory at Chelmsford Essex. The wheel will not turn and need freeing off. We can crane them onto a flatbed or trailer for you as they are not man handle-able. About 2 ton
Hand winch for use on boat trailer or small ATV trailer. 1200lbs capacity Brand new and unused Old Stock No belt or wire. smaller ones also available.
VINTAGE Oil LAMP GLASS CHIMNEY. 1920,S NEW OLD STOCK CHIMNEY. Height 155mm Top diameter 40mm Bottom diameter 53mm O/D We have more Lamps, Stoves and many spare parts for oil lamps and heaters. Bringing History Back To Life. If you need any more or parts e-mail or call
The engine has no name on it, that I can see, But I am told that it is a Petter A1 made in the1950's it starts and runs, it is mag start, I took the carb and tank off for the winter and have lost the filler cap, the compressor turns over and appears to work the valves may need servicing, there are no V belts so I have only run the engine. The compressor has a tank under the frame; there is a brass plate on the side it reads B.E.N. High Wycombe Type P12 S/No 1/7000844 Max PSI 75 as you can see in the photo it is on a steel wheeled frame but the tyres are rotten but the wheels go round.
Blacksmiths Forge and Leather Bellows very old, in need of repair, I have dismantled the forge for repair, and have no time or space to finish it, The forge has a large bellows of 28 inches diameter and needs restitching down the side, apart from that, they are in good condition for their age possibly 100 years old, the steel work needs a rebuild, all the casting are there, and the old steel is there, to use as pattens, The photo is before I dismantled it.
The Kosmos burner is probably the most popular burner used in European lamps. Oil lamp chimney Size 9 1/4" x1 7/16" Marked Best Fireproof Crystal. We Have over 50 of this size, all New but old stock. If you require a different size please email us as we have not sorted out all the lamp glass stock
Terex Amida diesel lighting tower Model GL4050D-4M4 Power Mast, by a 12v Winch 9m high, I think but I have not put a tape on it. Year 2002, Hours 3409, Kubota 3 cylinder engine, Key start, Rad cooled. 220 volt generator at 1500rpm, 7 Kva Running two split 110v circuits, one for tools and one for light. It runs 4 Metal Halide All 4 starter are there and working But someone stole two of the lights on a job, so there are only Two on it 1000w. There is also 4 1000 w Tungsten Halogen lamps that I have never used so I don't know if the Tungsten lamps are OK. The Kubota 3 cylinder Diesel Engine and the tower is in good working order. Towable Lighting Tower
This is a Centec A2 single phase universal milling machine with forward and reverse ideal for a model maker, it has a vertical head with a Clarkson auto lock chuck and collets and a ½” drill chuck and quill lever down movement, there is also a horizontal head with arbour and spacers. The machine is 86cm high 60cm wide 80cm deep the table is 40cm x 10.5cm there is a No2 Morse taper on the Vertical and Horizontal drives. This is a nice little machine and is in full working order and will fit in the back of a car with a struggle, please email if you need any more details or wish to see it running. I have replaced it with a Bridgeport.